BFT PHOBOS N BT Manuel d'utilisateur télécharger pdf (Page 4)

INSTALLATION MANUAL

ENGLISH

Thank you for buying this product, our company is sure that you will

be more than satisﬁed with the product’s performance. The product is

supplied with a “Warnings” leaﬂet and an “Instruction booklet”. These

should both be read carefully as they provide important information about

safety, installation, operation and maintenance. This product complies with

the recognised technical standards and safety regulations. We declare

that this product is in conformity with the following European Directives:

89/336/EEC and 73/23/EEC (and subsequent amendments).

1) GENERAL SAFETY

WARNING! An incorrect installation or improper use of the product

can cause damage to persons, animals or things.

• The “Warnings” leaﬂet and “Instruction booklet” supplied with this

product should be read carefully as they provide important information

about safety, installation, use and maintenance.

• Scrap packing materials (plastic, cardboard, polystyrene etc) according

to the provisions set out by current standards. Keep nylon or polystyrene

bags out of children’s reach.

• Keep the instructions together with the technical brochure for future

reference.

• This product was exclusively designed and manufactured for the use

speciﬁed in the present documentation. Any other use not speciﬁed

in this documentation could damage the product and be dangerous.

• The Company declines all responsibility for any consequences resulting

from improper use of the product, or use which is different from that

expected and speciﬁed in the present documentation.

• Do not install the product in explosive atmosphere.

• The construction components of this product must comply with the

following European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC

and subsequent amendments. As for all non-EEC countries, the above-

mentioned standards as well as the current national standards should

be respected in order to achieve a good safety level.

• The Company declines all responsibility for any consequences result-

ing from failure to observe Good Technical Practice when constructing

closing structures (door, gates etc.), as well as from any deformation

which might occur during use.

• The installation must comply with the provisions set out by the follow-

ing European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and

subsequent amendments.

• Disconnect the electrical power supply before carrying out any work

on the installation. Also disconnect any buffer batteries, if ﬁtted.

• Fit an omnipolar or magnetothermal switch on the mains power supply,

having a contact opening distance equal to or greater than 3,5 mm.

• Check that a differential switch with a 0.03A threshold is ﬁtted just

before the power supply mains.

• Check that earthing is carried out correctly: connect all metal parts for

closure (doors, gates etc.) and all system components provided with

an earth terminal.

• Fit all the safety devices (photocells, electric edges etc.) which are

needed to protect the area from any danger caused by squashing,

conveying and shearing.

• Position at least one luminous signal indication device (blinker) where

it can be easily seen, and ﬁx a Warning sign to the structure.

•

The Company declines all responsibility with respect to the automation

safety and correct operation when other manufacturers’ components

are used.

• Only use original parts for any maintenance or repair operation.

• Do not modify the automation components, unless explicitly authorised

by the company.

• Instruct the product user about the control systems provided and the

manual opening operation in case of emergency.

• Do not allow persons or children to remain in the automation operation

area.

• Keep radio control or other control devices out of children’s reach, in

order to avoid unintentional automation activation.

• The user must avoid any attempt to carry out work or repair on the

automation system, and always request the assistance of qualiﬁed

personnel.

• Anything which is not expressly provided for in the present instructions,

is not allow.

• Installation must be carried out using the safety devices and controls

prescribed by the EN 12978 Standard.

•

Check that the stated temperature range is compatible with the place

where the operator is to be installed.

• If present, the hold button (hold-to-run control) must be ﬁtted within

sight of the door but away from the moving parts, at a height of 1.5 m,

and must not be accessible to the public.

• If the operator is ﬁtted at a height lower than 2.5 m, you must guarantee

an adequate degree of protection for the electrical and mechanical

parts.

• Make sure that squashing is avoided between the moving parts and

surrounding ﬁxed parts. Fit all the safety devices (photocells, safety

edges etc.) required to protect the area from any danger of squashing,

drawing in and shearing.

• After completing the installation, ensure that the motor is set correctly

and that the protection and release systems operate correctly.

2) GENERAL OUTLINE

Electromechanical operator designed to automate residential-type ga-

tes.

The gearmotor keeps the gate locked on closing and on opening, without

needing an electric lock for leaves up to 3 m long. For leaves ranging

between 3m and 5m long, the electric lock becomes indispensable.

The operator is provided with an electronic torque limiter. It must be con-

trolled by an electronic control panel provided with torque setting.

The end-of-stroke operation is controlled by two magnetic limit devices.

The operator is provided with an obstacle detection system complying

with EN12453 and EN 12445 standards.

The following optional accessories are available on request:

- Buffer battery kit mod. PHOBOS-BT BAT

Allows operation of the automation even when there is no mains power

supply for a short period of time.

3) TECHNICAL SPECIFICATIONS

3.1) PHOBOS N BT

Power supply: .............................................................................. 24V

Motor revolutions: ....................................................................2500 min

-1

Absorbed power:..............................................................................40 W

Absorbed current: ............................................................................1.5 A

Push and pull force: ..................................................... 2000 N (~200 kg)

Working stroke: ...........................................................................

295 mm

Stem speed:...................................................................20 mm/s approx.

Impact reaction: ...................... Torque limiter aboard Libra control board

Limit devices: .............................. Magnetic, incorporated and adjustable

Manual manoeuvre: .......................................................CLS release key

No. of manoeuvres in 24hours: ....................................... 60 manoeuvres

Maximum leaf length: ................................................................ 1800 mm

Max. leaf weight: .......................................................... 2500 N (~250 kg)

Environmental conditions: ......................................from -20 °C to +50 °C

Protection level: .............................................................................. IP X4

Dimensions: ............................................................................... See ﬁg.1

Controller weight: ................................................................... 50N (~5kg)

Lubrication: .................................................................permanent grease

3.2) BATTERY KIT BT BAT

Charging voltage: ..................................................................... 27.2V

Charging current: ..........................................................................130mA

Outside temperature when values were measured: ........................ 25°C

Battery capacity: .............................................................. 2x (12V 1.2Ah)

Flat battery protection threshold: ............................................. 20.4V

Battery charging time: ............................................................... 12/14 hrs

4) INSTALLATION OF THE ACTUATOR

4.1) Preliminary checks

Check that:

• The gate structure is sufﬁciently sturdy.

• Also make sure that the actuator pushes against the leaf reinforced

section.

• The leaves move manually and without effort all along their stroke.

• If the gate has not been recently installed, check the wear condition of

all components.

• Repair or replace faulty or worn parts.

The automation reliability and safety are directly inﬂuenced by the state

of the gate structure.

• Fit the magnet-holder “M” by inserting it into the front bracket “F” until

a click is heard (as from Fig.7).

The diagram in ﬁg. 2 should be used as a reference for installation and

consult the table for the distances in mounting the gate post.

The diagram in ﬁg. 2 uses the following legend:

P Gate post rear fastening bracket

PHOBOS N BT Ver. 03 - 9

D811517_03

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

BFT PHOBOS N BT Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Outils de jardin BFT PHOBOS N BT